Datamax-oneil Class Series II Programmer’s Manual Manuel d'utilisateur Page 220
- Page / 334
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix G – Bar Code Details
206 Class Series 2 Programmer’s Manual
C: UPC-E
Valid Characters: 0-9
Length: Seven digits. If the user provides six digits, the printer will compute the
checksum. If the user provides the checksum, the printer will check that it matches the
expected checksum. If it does not match, the printer will print out all zeros and the
expected checksum.
Valid bar widths: The fourth character of record is the width of the narrow bar in dots.
All other bars are a ratio of the narrow bar (2 times, 3 times, and 4 times the narrow
bar width).
The following example prints a UPC-E bar code:
<STX>L
D11<CR>
1C0000000150100012345<CR>
121100000000100Barcode C<CR>
E
D: Interleaved 2 of 5 (I 2 of 5)
Valid Characters: 0-9
Variable Length.
Valid bar widths: The expected ratio of wide to narrow bars can range from 2:1 to 3:1.
The following example prints an Interleaved 2 of 5 bar code with a wide to narrow bar
ratio of 3:1:
<STX>L
D11<CR>
1D000000015010001234567890<CR>
121100000000100Barcode D<CR>
E
E: Code 128
Valid Characters: The entire 128 ASCII character set.
Variable Length
Valid bar widths: The fourth character of record is the width of the narrow bar in dots.
All other bars are a ratio of the narrow bar (2 times the narrow bar width, 3 times the
narrow bar width, and 4 times the narrow bar width).
- Class Series II 1
- Contents 7
- Overview 15
- General Conventions 17
- Special Instructions 18
- Typical Data Flow Sequence 18
- Configuration Commands 19
- ) commands can be changed at 21
- Alternate Control Code Modes 24
- Immediate Command Functions 26
- SOH B Toggle Pause 27
- SOH C Stop/Cancel 28
- SOH D SOH Shutdown 28
- SOH F Send Status Byte 29
- STX e Select Edge Sensor 34
- STX F Form Feed 34
- STX I Input Image Data 35
- STX k Test RS-232 Port 37
- STX o Cycle Cutter 40
- STX P Set Hex Dump Mode 40
- STX p Controlled Pause 40
- STX Q Clear All Modules 41
- STX q Clear Module 41
- STX R Ribbon Saver Control 41
- STX S Set Feed Speed 42
- STX T Print Quality Label 42
- STX X Set Default Module 47
- STX z Pack Module 50
- STX Kb Backfeed Time Delay 55
- STX KC Get Configuration 56
- STX Kc Configuration Set 57
- (if available) 58
- (MP Comapct4 Mark II only) 63
- (for firmware versions 67
- 14.00 and later) 67
- 13.99 and earlier) 67
- (continued) 74
- STX KE Character Encoding 117
- STX KI GPIO Input 122
- STX Kn NIC Reset 122
- STX KO GPIO Output 123
- STX Kp Module Protection 124
- Introduction 139
- A Set Format Attribute 140
- C Set Column Offset Amount 141
- B Bar Code Magnification 141
- H Enter Heat Setting 145
- J Justification 145
- M Select Mirror Mode 146
- P Set Print Speed 147
- R Set Row Offset Amount 148
- S Set Feed Speed 150
- Embedding 155
- ^ Set Count by Amount 156
- STX D Print adjusted date 157
- STX T Print Time and Date 158
- )s###W Font Descriptor 162
- *c###E Character Code 162
- Generating Label Formats 163
- Generating Records 164
- The Structure of a Record 164
- Record Structure Types 168
- 176
- Figure 1 178
- Figure 2 178
- Figure 3 179
- Appendix A 181
- ASCII Control Chart 181
- 10K OHM 1/4 WATT 183
- Appendix B – Sample Programs 184
- Appendix C 193
- Appendix C – Available Fonts 196
- Appendix D 199
- Reset Codes 199
- Appendix D – Reset Codes 200
- Single Byte Symbol Sets 201
- Appendix F 213
- Bar Code Summary Data 213
- Appendix G 219
- Bar Code Details 219
- Barcode I 224
- Barcode S 228
- Barcode T 228
- Barcode U 231
- Barcode z 232
- Barcode Z 233
- Barcode W1c 235
- Barcode W1C 236
- Barcode W1D 240
- Barcode W1f 245
- Barcode W1F 245
- Barcode W1G 246
- Barcode W1I 248
- Barcode W1J 249
- Barcode W1k 251
- Barcode W1L 253
- Barcode W1M 255
- Barcode W1m 255
- Barcode W1N 255
- (IMB) 256
- 34 567890 123 4567 258
- Barcode W1t 259
- Barcode W1Y 260
- Barcode W1Z 262
- Appendix H 265
- Appendix J 271
- • Pins 1 – 2 = +5VDC; 277
- • Pins 2 – 3 = +24VDC; or 277
- • None = A common external 277
- Signal Out 280
- Signal In 280
- I-Class GPIO 281
- M-Class II GPIO 282
- Maximum Format Fields 285
- Appendix L 289
- Speed Ranges 289
- Appendix M 291
- Commands by Function 291
- Appendix N 293
- Image Loading 293
- Appendix N – Image Loading 294
- Figure N-2: Sample Label 294
- Appendix O 295
- Programming Examples 297
- ILPC - Kanji 298
- ILPC - Chinese 302
- ILPC - Korean 305
- Appendix Q 307
- Plug and Play IDs 307
- Appendix R 309
- Line Mode 309
- Appendix R – Line Mode 310
- Appendix S 313
- RFID Overview 313
- Label Formatting Mode 314
- Appendix S – RFID Overview 316
- Field Valid Inputs Meaning 317
- GEN2 Kill/Access Passwords 318
- GEN2 Lock States 318
- Appendix T 319
- WiFi Region Country Codes 319
- Appendix U 325
- Graphics Display Icon Key 325
- Appendix V 329
- Glossary 331
Produits connexes et manuels pour Imprimeurs Datamax-oneil Class Series II Programmer’s Manual
(58 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels