Datamax-oneil Class Series II Programmer’s Manual Manuel d'utilisateur Page 26
- Page / 334
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Immediate Command Functions
12 Class Series 2 Programmer’s Manual
SOH A Send ASCII Status String
This command allows the host computer to check the current printer status. The printer
returns a string of eight characters, followed by a carriage return. Each character (see
below) indicates an associated condition, either true (Y) or false (N). Byte 1 is
transmitted first. See <SOH>F.
Syntax:
<
SOH>
A
Sample:
<SOH>A
Printer Response:
abcdefgh<CR>
Where:
Possible
Values
Interpretation
Transmit
Sequence
a
-
Y/N
Y
=
Interpreter busy (imaging) 1
b
-
Y/N
Y
=
Paper out or fault 2
c
-
Y/N
Y
=
Ribbon out or fault 3
d
-
Y/N
Y
=
Printing batch 4
e
-
Y/N
Y
=
Busy printing 5
f
-
Y/N
Y
=
Printer paused 6
g
-
Y/N
Y
=
Label presented 7
h
-
Y/N
Y
=
(Internal) Rewinder out or fault 8
Table 3-1: ASCII Status Bytes
SOH a Send ASCII Extended Status String
This command allows the host computer to check an extended current printer status.
The printer returns a string of seventeen characters, followed by a carriage return. Most
characters (see below) indicate an associated condition, either true (Y) or false (N). Byte
1 is transmitted first. See <SOH>F.
Syntax:
<
SOH>a
Sample:
<SOH>a
Printer Response:
abcdefgh:ijklmnop<CR>
- Class Series II 1
- Contents 7
- Overview 15
- General Conventions 17
- Special Instructions 18
- Typical Data Flow Sequence 18
- Configuration Commands 19
- ) commands can be changed at 21
- Alternate Control Code Modes 24
- Immediate Command Functions 26
- SOH B Toggle Pause 27
- SOH C Stop/Cancel 28
- SOH D SOH Shutdown 28
- SOH F Send Status Byte 29
- STX e Select Edge Sensor 34
- STX F Form Feed 34
- STX I Input Image Data 35
- STX k Test RS-232 Port 37
- STX o Cycle Cutter 40
- STX P Set Hex Dump Mode 40
- STX p Controlled Pause 40
- STX Q Clear All Modules 41
- STX q Clear Module 41
- STX R Ribbon Saver Control 41
- STX S Set Feed Speed 42
- STX T Print Quality Label 42
- STX X Set Default Module 47
- STX z Pack Module 50
- STX Kb Backfeed Time Delay 55
- STX KC Get Configuration 56
- STX Kc Configuration Set 57
- (if available) 58
- (MP Comapct4 Mark II only) 63
- (for firmware versions 67
- 14.00 and later) 67
- 13.99 and earlier) 67
- (continued) 74
- STX KE Character Encoding 117
- STX KI GPIO Input 122
- STX Kn NIC Reset 122
- STX KO GPIO Output 123
- STX Kp Module Protection 124
- Introduction 139
- A Set Format Attribute 140
- C Set Column Offset Amount 141
- B Bar Code Magnification 141
- H Enter Heat Setting 145
- J Justification 145
- M Select Mirror Mode 146
- P Set Print Speed 147
- R Set Row Offset Amount 148
- S Set Feed Speed 150
- Embedding 155
- ^ Set Count by Amount 156
- STX D Print adjusted date 157
- STX T Print Time and Date 158
- )s###W Font Descriptor 162
- *c###E Character Code 162
- Generating Label Formats 163
- Generating Records 164
- The Structure of a Record 164
- Record Structure Types 168
- 176
- Figure 1 178
- Figure 2 178
- Figure 3 179
- Appendix A 181
- ASCII Control Chart 181
- 10K OHM 1/4 WATT 183
- Appendix B – Sample Programs 184
- Appendix C 193
- Appendix C – Available Fonts 196
- Appendix D 199
- Reset Codes 199
- Appendix D – Reset Codes 200
- Single Byte Symbol Sets 201
- Appendix F 213
- Bar Code Summary Data 213
- Appendix G 219
- Bar Code Details 219
- Barcode I 224
- Barcode S 228
- Barcode T 228
- Barcode U 231
- Barcode z 232
- Barcode Z 233
- Barcode W1c 235
- Barcode W1C 236
- Barcode W1D 240
- Barcode W1f 245
- Barcode W1F 245
- Barcode W1G 246
- Barcode W1I 248
- Barcode W1J 249
- Barcode W1k 251
- Barcode W1L 253
- Barcode W1M 255
- Barcode W1m 255
- Barcode W1N 255
- (IMB) 256
- 34 567890 123 4567 258
- Barcode W1t 259
- Barcode W1Y 260
- Barcode W1Z 262
- Appendix H 265
- Appendix J 271
- • Pins 1 – 2 = +5VDC; 277
- • Pins 2 – 3 = +24VDC; or 277
- • None = A common external 277
- Signal Out 280
- Signal In 280
- I-Class GPIO 281
- M-Class II GPIO 282
- Maximum Format Fields 285
- Appendix L 289
- Speed Ranges 289
- Appendix M 291
- Commands by Function 291
- Appendix N 293
- Image Loading 293
- Appendix N – Image Loading 294
- Figure N-2: Sample Label 294
- Appendix O 295
- Programming Examples 297
- ILPC - Kanji 298
- ILPC - Chinese 302
- ILPC - Korean 305
- Appendix Q 307
- Plug and Play IDs 307
- Appendix R 309
- Line Mode 309
- Appendix R – Line Mode 310
- Appendix S 313
- RFID Overview 313
- Label Formatting Mode 314
- Appendix S – RFID Overview 316
- Field Valid Inputs Meaning 317
- GEN2 Kill/Access Passwords 318
- GEN2 Lock States 318
- Appendix T 319
- WiFi Region Country Codes 319
- Appendix U 325
- Graphics Display Icon Key 325
- Appendix V 329
- Glossary 331
Produits connexes et manuels pour Imprimeurs Datamax-oneil Class Series II Programmer’s Manual
(58 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels