Datamax-oneil DPL Programmer’s Manual Manuel d'utilisateur Page 150
- Page / 296
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Generating Label Formats
142
Field Valid Inputs Meaning
eee
000 to 999 (000 to 099 Reserved), A04 to A72, x04 – x72,
Where x is an upper case letter; see Appendix H.
Font / Size
ffff
0000 to 9999 Row
gggg
0000 to 9999 Dependent upon printer. See Appendix K. Column
jj…j
Valid ASCII character string up to 255 characters followed by a
termination character.
Data
3: Scalable Fonts
The Smooth Scalable Font Technology is licensed from AGFA. Both Microtype and
TrueType (.TTF) Scalable Font file formats are supported. The eee field identifies
the scalable font*, and data type – normal (binary) or Hex ASCII. Uppercase S or U
– binary, lowercase u – Hex ASCII (see Appendix H). Values S00 to S9z, and U00 to
U9z (u00 to u9z), select a scalable font. S00, S01 and SAx are used for the
standard internal (resident) fonts.
Field Valid Inputs Meaning
a
1, 2, 3 and 4 Rotation
b
9 Fixed Value
c
1 to 9, A to Z, and a to z Width Multiplier
d
1 to 9, A to Z, and a to z Height Multiplier
eee
S00 to Szz, U00-Uzz, u00-uzz Font Data Type
ffff
0000 to 9999 Row
gggg
Dependent upon printer. See Appendix K. Column
hhhh
P004-P999, 0016-4163**
Character Height;
points, dots
iiii
P004-P999, 0014-4163**
Character Width;
points, dots
jj…j
Valid ASCII character string up to 255 characters followed by a
termination character.
Data
* The actual scalable font available is depending on your printer model and equipped options.
**Character sizes are resolution dependent, as indicated in the following table.
- Programmer’s Manual 1
- Contents 3
- 1 Overview 9
- General Conventions 10
- Special Instructions 10
- Typical Data Flow Sequence 11
- ) commands can be changed at 13
- Overview 14
- 15
- Alternate Control Code Modes 16
- Immediate Command Functions 17
- SOH B Toggle Pause 19
- SOH C Stop/Cancel 20
- SOH D SOH Shutdown 20
- SOH F Send Status Byte 21
- STX A Set Time and Date 23
- STX I Input Image Data 27
- STX o Cycle Cutter 30
- STX P Set Hex Dump Mode 31
- STX p Controlled Pause 31
- STX Q Clear All Modules 31
- STX q Clear Module 32
- STX R Ribbon Saver Control 32
- STX S Set Feed Speed 33
- STX T Print Quality Label 33
- STX X Set Default Module 37
- STX z Pack Module 40
- Extended System-Level 41
- STX Kb Backfeed Time Delay 44
- STX KC Get Configuration 45
- STX Kc Configuration Set 48
- STX KE Character Encoding 101
- STX KH Dot Check 104
- STX KI GPIO Input 106
- STX Kn NIC Reset 106
- STX KO GPIO Output 107
- STX Kp Module Protection 108
- Label Formatting 119
- Command Functions 119
- A Set Format Attribute 120
- B Bar Code Magnification 121
- C Set Column Offset Amount 121
- H Enter Heat Setting 124
- J Justification 125
- M Select Mirror Mode 125
- P Set Print Speed 126
- of .37 128
- S Set Feed Speed 130
- Embedding 135
- STX D Print adjusted date 137
- STX T Print Time and Date 138
- Introduction 141
- )s###W Font Descriptor 142
- *c###E Character Code 142
- 8 Generating Label Formats 143
- Generating Records 144
- The Structure of a Record 144
- Record Structure Types 148
- Fill Patterns 155
- Generating Label Formats 158
- Appendix A 161
- 10K OHM 1/4 WATT 163
- Appendix B – Sample Programs 164
- Appendix C 173
- Appendix C – Available Fonts 176
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- Appendix E – Symbol Sets 192
- Appendix F 193
- Appendix G 199
- Barcode I 204
- Barcode S 208
- Barcode T 208
- Barcode U 211
- Barcode z 212
- Barcode Z 213
- Barcode W1c 215
- Barcode W1C 216
- Barcode W1D 220
- Barcode W1f 225
- Barcode W1F 225
- Barcode W1G 226
- Barcode W1I 228
- Barcode W1J 229
- Barcode W1k 231
- Barcode W1L 233
- Barcode W1M 235
- Barcode W1m 235
- Barcode W1N 235
- (IMB) 236
- 34 567890 123 4567 238
- Barcode W1t 239
- Barcode W1Y 240
- Barcode W1Z 242
- Appendix H 245
- Appendix I 247
- Appendix J 251
- • Pins 1 – 2 = +5VDC; 252
- • Pins 2 – 3 = +24VDC; or 252
- • None = A common external 252
- Appendix K 253
- Appendix L 255
- Appendix M 257
- Appendix N 259
- Appendix N – Image Loading 260
- Appendix O 261
- Appendix P 263
- Appendix Q 273
- Appendix R 275
- Appendix R – Line Mode 276
- Appendix S 279
- Appendix S – RFID Overview 280
- Field Valid Inputs Meaning 283
- Appendix T 285
- Appendix U 291
- Glossary 293
Produits connexes et manuels pour Imprimeurs Datamax-oneil DPL Programmer’s Manual
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels