Datamax-oneil DPL Programmer’s Manual Manuel d'utilisateur Page 83
- Page / 296
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Extended System-Level Command Functions
75
WIFI Settings
# Ezprint Name Value Type
Description
40 CTC:T:H|P Network Type Unsigned
char
H: AdHoc
P:Infrastructure
41 CTC:E:<value> ESSID String 128 characters + 1 NULL terminated string
42 CTC:NA:<value> Network Authentication Type Enumeratio
n type or
unsigned
short
NET_AUTH_TYPE_NONE =0
NET_AUTH_TYPE_LEAP=1
NET_AUTH_TYPE_WPA_PSK=2 (WPA Personal)
NET_AUTH_TYPE_WPA=3 (WPA Enterprise)
NET_AUTH_TYPE_WPA_LEAP = 4 (obsolete)
NET_AUTH_TYPE_WPA2_PSK=5 (WPA2 Personal)
NET_AUTH_TYPE_WPA2=6 (WPA2 Enterprise)
NET_AUTH_TYPE_HOST_BASED_EAP=7
43 CTC:ET:<value> EAP Type Unsigned
char
EAP-LEAP (17)
EAP-TTLS (21)
EAP-PEAP (25)
EAP-FAST (43)
44 CTC:P2M:<value> Phase 2 Method Unsigned
char
Inner authentication:
0: None
EAP-GTC: 1 (Default)
EAP-MSCHAPV2: 2
EAP-MD5: 3
GTC: 4
MSCHAPV2: 5
MSCHAP: 6
CHAP: 7
EAP-TLS: 8
45 CTC:LU:<value> User Name String 128 characters + 1 NULL terminated char; Write ONLY
attribute!
46 CTC:LH:<value> User Password String 128 characters + 1 NULL terminated char; Write ONLY
attribute!
47 CTC:LU2:<value> Pass Phrase String 63 characters + 1 NULL terminated char; Write ONLY
attribute!
48 CTC:W:1|2 WEP data encryption Unsigned
char
1: Enable WEP data encryption
2: Allow WEP unencrypted traffic (Default)
49
CTC:S:0|5|13 WEP AP authentication Unsigned
char
Indicate the AP authentication method via WEP. The value
specifies the WEP key length.
0: Open
5: uses Shared Key 40- bit WEP key
13: uses Shared Key 128-bit WEP key
50 CTC:K:1|2|3|4 WEP Key Selected Unsigned
char
Indicates which WEP key is currently selected for WEP AP
authentication, if specify.
- Programmer’s Manual 1
- Contents 3
- 1 Overview 9
- General Conventions 10
- Special Instructions 10
- Typical Data Flow Sequence 11
- ) commands can be changed at 13
- Overview 14
- 15
- Alternate Control Code Modes 16
- Immediate Command Functions 17
- SOH B Toggle Pause 19
- SOH C Stop/Cancel 20
- SOH D SOH Shutdown 20
- SOH F Send Status Byte 21
- STX A Set Time and Date 23
- STX I Input Image Data 27
- STX o Cycle Cutter 30
- STX P Set Hex Dump Mode 31
- STX p Controlled Pause 31
- STX Q Clear All Modules 31
- STX q Clear Module 32
- STX R Ribbon Saver Control 32
- STX S Set Feed Speed 33
- STX T Print Quality Label 33
- STX X Set Default Module 37
- STX z Pack Module 40
- Extended System-Level 41
- STX Kb Backfeed Time Delay 44
- STX KC Get Configuration 45
- STX Kc Configuration Set 48
- STX KE Character Encoding 101
- STX KH Dot Check 104
- STX KI GPIO Input 106
- STX Kn NIC Reset 106
- STX KO GPIO Output 107
- STX Kp Module Protection 108
- Label Formatting 119
- Command Functions 119
- A Set Format Attribute 120
- B Bar Code Magnification 121
- C Set Column Offset Amount 121
- H Enter Heat Setting 124
- J Justification 125
- M Select Mirror Mode 125
- P Set Print Speed 126
- of .37 128
- S Set Feed Speed 130
- Embedding 135
- STX D Print adjusted date 137
- STX T Print Time and Date 138
- Introduction 141
- )s###W Font Descriptor 142
- *c###E Character Code 142
- 8 Generating Label Formats 143
- Generating Records 144
- The Structure of a Record 144
- Record Structure Types 148
- Fill Patterns 155
- Generating Label Formats 158
- Appendix A 161
- 10K OHM 1/4 WATT 163
- Appendix B – Sample Programs 164
- Appendix C 173
- Appendix C – Available Fonts 176
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- Appendix E – Symbol Sets 192
- Appendix F 193
- Appendix G 199
- Barcode I 204
- Barcode S 208
- Barcode T 208
- Barcode U 211
- Barcode z 212
- Barcode Z 213
- Barcode W1c 215
- Barcode W1C 216
- Barcode W1D 220
- Barcode W1f 225
- Barcode W1F 225
- Barcode W1G 226
- Barcode W1I 228
- Barcode W1J 229
- Barcode W1k 231
- Barcode W1L 233
- Barcode W1M 235
- Barcode W1m 235
- Barcode W1N 235
- (IMB) 236
- 34 567890 123 4567 238
- Barcode W1t 239
- Barcode W1Y 240
- Barcode W1Z 242
- Appendix H 245
- Appendix I 247
- Appendix J 251
- • Pins 1 – 2 = +5VDC; 252
- • Pins 2 – 3 = +24VDC; or 252
- • None = A common external 252
- Appendix K 253
- Appendix L 255
- Appendix M 257
- Appendix N 259
- Appendix N – Image Loading 260
- Appendix O 261
- Appendix P 263
- Appendix Q 273
- Appendix R 275
- Appendix R – Line Mode 276
- Appendix S 279
- Appendix S – RFID Overview 280
- Field Valid Inputs Meaning 283
- Appendix T 285
- Appendix U 291
- Glossary 293
Produits connexes et manuels pour Imprimeurs Datamax-oneil DPL Programmer’s Manual
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels