Datamax-oneil DPL Programmer’s Manual Manuel d'utilisateur Page 81
- Page / 296
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Extended System-Level Command Functions
73
DNS Settings
# Ezprint Name Value Type
Description
1 CTC:SDNS:Y|N Enable Static DNS String – 1
char long
Using Static DNS or not. Default value is “N”.
2 CTC:DNS1:***.***.***.*** Preferred DNS Server IP4 string
format
IP address for preferred DNS server
3 CTC:DNS2:***.***.***.*** Secondary DNS Server IP4 string
format
IP address for secondary DNS server
4 CTC:DSUF:<DNS Suffix> DNS Suffix String 64 characters string + 1 NULL terminated character
Network Settings
# Ezprint Name Value Type
Description
20 CTC:I2:<value> Inactive Timeout Unsigned
short
Current connection will terminated if no network traffic
after a specific interval. Default value is 30 seconds
21 CTC:D:N|B|Y IP address method Unsigned
char
N: use static IP address
B: BootB enable
Y:DHCP enable
22 CTC:I:xxx.xxx.xxx.xxx Active IP address (READ ONLY)
String This field is holding the value of the current active IP
address. As the result of the query request:
1. If “IP address method” is set to “use static IP
address”, this field will hold the value of “Static IP
address”.
2. Otherwise, it will hold the value of the current active
IP address.
This field is using for reporting only. In order to set the
value for static IP address, use item number 32.
23 CTC:M:xxx.xxx.xxx.xxx Active Subnet mask (READ
ONLY)
String This field is holding the value of current active Subnet mask
address.
As the result of the query request:
1. If “IP address method” is set to “use static Subnet
mask address”, this field will hold the value of “Static
Subnet mask address”.
2. Otherwise, it will hold the value of the current active
Subnet mask address.
This field is using for reporting only. In order to set the
value for static Subnet mask address, use item number 33.
- Programmer’s Manual 1
- Contents 3
- 1 Overview 9
- General Conventions 10
- Special Instructions 10
- Typical Data Flow Sequence 11
- ) commands can be changed at 13
- Overview 14
- 15
- Alternate Control Code Modes 16
- Immediate Command Functions 17
- SOH B Toggle Pause 19
- SOH C Stop/Cancel 20
- SOH D SOH Shutdown 20
- SOH F Send Status Byte 21
- STX A Set Time and Date 23
- STX I Input Image Data 27
- STX o Cycle Cutter 30
- STX P Set Hex Dump Mode 31
- STX p Controlled Pause 31
- STX Q Clear All Modules 31
- STX q Clear Module 32
- STX R Ribbon Saver Control 32
- STX S Set Feed Speed 33
- STX T Print Quality Label 33
- STX X Set Default Module 37
- STX z Pack Module 40
- Extended System-Level 41
- STX Kb Backfeed Time Delay 44
- STX KC Get Configuration 45
- STX Kc Configuration Set 48
- STX KE Character Encoding 101
- STX KH Dot Check 104
- STX KI GPIO Input 106
- STX Kn NIC Reset 106
- STX KO GPIO Output 107
- STX Kp Module Protection 108
- Label Formatting 119
- Command Functions 119
- A Set Format Attribute 120
- B Bar Code Magnification 121
- C Set Column Offset Amount 121
- H Enter Heat Setting 124
- J Justification 125
- M Select Mirror Mode 125
- P Set Print Speed 126
- of .37 128
- S Set Feed Speed 130
- Embedding 135
- STX D Print adjusted date 137
- STX T Print Time and Date 138
- Introduction 141
- )s###W Font Descriptor 142
- *c###E Character Code 142
- 8 Generating Label Formats 143
- Generating Records 144
- The Structure of a Record 144
- Record Structure Types 148
- Fill Patterns 155
- Generating Label Formats 158
- Appendix A 161
- 10K OHM 1/4 WATT 163
- Appendix B – Sample Programs 164
- Appendix C 173
- Appendix C – Available Fonts 176
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- Appendix E – Symbol Sets 192
- Appendix F 193
- Appendix G 199
- Barcode I 204
- Barcode S 208
- Barcode T 208
- Barcode U 211
- Barcode z 212
- Barcode Z 213
- Barcode W1c 215
- Barcode W1C 216
- Barcode W1D 220
- Barcode W1f 225
- Barcode W1F 225
- Barcode W1G 226
- Barcode W1I 228
- Barcode W1J 229
- Barcode W1k 231
- Barcode W1L 233
- Barcode W1M 235
- Barcode W1m 235
- Barcode W1N 235
- (IMB) 236
- 34 567890 123 4567 238
- Barcode W1t 239
- Barcode W1Y 240
- Barcode W1Z 242
- Appendix H 245
- Appendix I 247
- Appendix J 251
- • Pins 1 – 2 = +5VDC; 252
- • Pins 2 – 3 = +24VDC; or 252
- • None = A common external 252
- Appendix K 253
- Appendix L 255
- Appendix M 257
- Appendix N 259
- Appendix N – Image Loading 260
- Appendix O 261
- Appendix P 263
- Appendix Q 273
- Appendix R 275
- Appendix R – Line Mode 276
- Appendix S 279
- Appendix S – RFID Overview 280
- Field Valid Inputs Meaning 283
- Appendix T 285
- Appendix U 291
- Glossary 293
Produits connexes et manuels pour Imprimeurs Datamax-oneil DPL Programmer’s Manual
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels