Datamax-oneil DPL Programmer’s Manual Manuel d'utilisateur Page 261
- Page / 296
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix O – UPC-A and EAN-13 Variable Price / Weights
253
Appendix O
UPC-A and EAN-13: Variable Price/Weight Bar Codes
The EAN/UPC standard allows for an additional checksum to be generated in the middle of
the bar code based on the data. This is used when the price or weight of an item is
embedded into the bar code data (commonly used in the food industry).
For the printer to generate this checksum, a “V” must be placed in the data stream in the
position the checksum is requested. If the “V” is placed in the 6th position for UPC-A or the
7th position for EAN-13, a checksum will be generated using the next five digits in the data
stream. If the “V” is placed in the 7th position for UPC-A or the 8th position for EAN-13, a
checksum will be generated using the next four digits in the data stream. The checksum is
generated per the EAN/UPC bar code standard.
Examples:
1B110000200020012345V01199
Prints the UPC-A bar code with the variable price checksum in the sixth position.
1B1100002000200123456V0150
Prints the UPC-A bar code with the variable price checksum in the seventh position.
1F1100002000200123456V01199
Prints the EAN-13 bar code with the variable price checksum in the seventh position.
1F11000020002001234567V0150
Prints the EAN-13 bar code with the variable price checksum in the eighth position.
- Programmer’s Manual 1
- Contents 3
- 1 Overview 9
- General Conventions 10
- Special Instructions 10
- Typical Data Flow Sequence 11
- ) commands can be changed at 13
- Overview 14
- 15
- Alternate Control Code Modes 16
- Immediate Command Functions 17
- SOH B Toggle Pause 19
- SOH C Stop/Cancel 20
- SOH D SOH Shutdown 20
- SOH F Send Status Byte 21
- STX A Set Time and Date 23
- STX I Input Image Data 27
- STX o Cycle Cutter 30
- STX P Set Hex Dump Mode 31
- STX p Controlled Pause 31
- STX Q Clear All Modules 31
- STX q Clear Module 32
- STX R Ribbon Saver Control 32
- STX S Set Feed Speed 33
- STX T Print Quality Label 33
- STX X Set Default Module 37
- STX z Pack Module 40
- Extended System-Level 41
- STX Kb Backfeed Time Delay 44
- STX KC Get Configuration 45
- STX Kc Configuration Set 48
- STX KE Character Encoding 101
- STX KH Dot Check 104
- STX KI GPIO Input 106
- STX Kn NIC Reset 106
- STX KO GPIO Output 107
- STX Kp Module Protection 108
- Label Formatting 119
- Command Functions 119
- A Set Format Attribute 120
- B Bar Code Magnification 121
- C Set Column Offset Amount 121
- H Enter Heat Setting 124
- J Justification 125
- M Select Mirror Mode 125
- P Set Print Speed 126
- of .37 128
- S Set Feed Speed 130
- Embedding 135
- STX D Print adjusted date 137
- STX T Print Time and Date 138
- Introduction 141
- )s###W Font Descriptor 142
- *c###E Character Code 142
- 8 Generating Label Formats 143
- Generating Records 144
- The Structure of a Record 144
- Record Structure Types 148
- Fill Patterns 155
- Generating Label Formats 158
- Appendix A 161
- 10K OHM 1/4 WATT 163
- Appendix B – Sample Programs 164
- Appendix C 173
- Appendix C – Available Fonts 176
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- Appendix E – Symbol Sets 192
- Appendix F 193
- Appendix G 199
- Barcode I 204
- Barcode S 208
- Barcode T 208
- Barcode U 211
- Barcode z 212
- Barcode Z 213
- Barcode W1c 215
- Barcode W1C 216
- Barcode W1D 220
- Barcode W1f 225
- Barcode W1F 225
- Barcode W1G 226
- Barcode W1I 228
- Barcode W1J 229
- Barcode W1k 231
- Barcode W1L 233
- Barcode W1M 235
- Barcode W1m 235
- Barcode W1N 235
- (IMB) 236
- 34 567890 123 4567 238
- Barcode W1t 239
- Barcode W1Y 240
- Barcode W1Z 242
- Appendix H 245
- Appendix I 247
- Appendix J 251
- • Pins 1 – 2 = +5VDC; 252
- • Pins 2 – 3 = +24VDC; or 252
- • None = A common external 252
- Appendix K 253
- Appendix L 255
- Appendix M 257
- Appendix N 259
- Appendix N – Image Loading 260
- Appendix O 261
- Appendix P 263
- Appendix Q 273
- Appendix R 275
- Appendix R – Line Mode 276
- Appendix S 279
- Appendix S – RFID Overview 280
- Field Valid Inputs Meaning 283
- Appendix T 285
- Appendix U 291
- Glossary 293
Produits connexes et manuels pour Imprimeurs Datamax-oneil DPL Programmer’s Manual
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels